Fast, Tap-Proof Data Networks with Light

The demonstrator module is plugged right into an electrical outlet, extracting the data from the power line.
© Fraunhofer HHI

The digital transformation means that more and more devices such as X-ray and ultrasound machines are being connected to networks in hospital settings, for example. These kinds of equipment have to be movable as needed. In the LINCNET project, Fraunhofer researchers are using light to transmit data to machines and robots in clinical settings and industrial production environments. Combining electrical networks with the ultra-fast 5G mobile network creates powerful and low-cost wireless networks for buildings. When deployed in hospitals, this solution means devices connect wirelessly to the network — with lower electromagnetic emissions.

Manufacturing in advanced Industry 4.0 scenarios is geared toward constant change. Order changes occurring on short notice require machines, robots, and measuring instruments to be rearranged quickly and incorporated into retooled production flows. The same applies to healthcare.

In both cases, conventional networks, in which machines and devices are connected via Wi-Fi, are not always optimal. In production settings, the various wireless networks can interfere with each other in unforeseeable ways. And in sensitive environments like hospital operating rooms, electromagnetic emissions from these networks are also an issue, as strict limits apply there. On top of that, there are data security risks. While the data traffic is encrypted, the wireless network itself remains fundamentally open to potential attackers.

Researchers from the Fraunhofer Institute for Telecommunications, Heinrich-Hertz-Institut, HHI in Berlin are working with project partners on a promising solution: data transmission via light. In the LINCNET (LiFi-enabled 5G for INdustrial and MediCal NETworks) project, the Fraunhofer researchers are harnessing the possibility of transmitting data by modulating light pulses. Standard commercially available LEDs and photodiodes are used as a light source and receiver, respectively.

Powerline: data fed via the electrical network

Numerous applications call for combining the ultra-fast 5G networks with data transmission via light. One promising approach is reuse of the existing electrical network (power line communication, or PLC) to bring the data to the ceiling in every room and wirelessly transmit it the last few meters there using light (LiFi). The light signals do not pass through walls. This reduces electromagnetic emissions and is more energy efficient. PLC eliminates the need for costly laying of additional cables for the network. Aachen-based company devolo Solutions GmbH, the lead entity in the LINCNET consortium, is responsible for PLC development and optimization. A LiFi module converts the data from the electrical network into impulses modulating the light signals. The light is continuously modulated by making it brighter and darker. The LEDs transmit their data to end devices equipped with transceiver units. The signal changes take place 100 million times a second and are not perceived by the human eye.

LiFi has clear advantages over wireless transmission of data. The data transmission itself is extremely robust and powerful. Within local networks, it enables latency times of under 2 milliseconds and transmission rates of up to 1 Gigabit per second. Project manager Lennert Bober points out additional advantages: “Light doesn’t penetrate through walls, so there’s no way to eavesdrop on it. The data transmission is also not affected by other wireless networks or by machines that emit radiation that could interfere with it, and it doesn’t affect them, either.” Since the data are only transmitted within the cone of light itself, it is possible to supply many different machines or devices with data all at once without the light signals interfering with each other.

Ceiling module converts data to light signals

The Fraunhofer HHI team is relying on its decades of expertise in harnessing light to transmit data. Fraunhofer HHI co-developed LiFi and is also active to standardize this technology. For the LINCNET project, the researchers have developed a ceiling module with a digital signal processor (DSP). It extracts the data from the flow of electricity and converts them into pulses for digital modulation of the light source. The LED transmits the data from the ceiling to the end device placed within the cone of light, which could be a robot in a manufacturing setting or an ultrasound unit in a medical center, for example. The data is isolated inside the cone of light just as it would be inside a cable. “It’s just as secure as a cable network and performs equally well — just without cables,” Bober explains.

Light has another crucial advantage in industrial applications, too. The spectrum can be used in any way desired, as the regulations that apply to radio do not exist for light. “Industry players don’t have to request permission to use a certain frequency or pay licensing fees,” Bober adds.

Highly scalable LiFi networks

The researchers from Fraunhofer HHI are also already working to further improve LiFi networks as part of the project. While using PLC to connect LiFi to the electrical network, they are also developing a combination involving fast Ethernet-based networks. While backhaul connections for wireless access points via Ethernet are common, this relies on a centralized approach similar to that used in 5G mobile networks. In this kind of fronthaul network, each LiFi ceiling module has an Ethernet connection to a central unit, which makes it possible to coordinate LiFi transmissions on a space-time granular basis, significantly enhancing performance. “Highly scalable Ethernet connections paired with LiFi are a wonderful combination for real-time control of robots or high-end scenarios in medicine,” Bober says.

For companies and hospitals alike, LINCNET can provide a noticeable boost for further digitalization and promote technological sovereignty in Germany by building skills in optical wireless communication. The German Federal Ministry for Economic Affairs and Climate Action (BMWK) is providing 3.3 million Euros in funding to support the 15 partners involved in the LINCNET project.

Weitere Informationen:

https://www.fraunhofer.de/en/press/research-news/2024/august-2024/fast-tap-proof…

Media Contact

Ronja Schillings Press Officer
Fraunhofer Institute for Telecommunications, Heinrich-Hertz-Institut, HHI

All latest news from the category: Power and Electrical Engineering

This topic covers issues related to energy generation, conversion, transportation and consumption and how the industry is addressing the challenge of energy efficiency in general.

innovations-report provides in-depth and informative reports and articles on subjects ranging from wind energy, fuel cell technology, solar energy, geothermal energy, petroleum, gas, nuclear engineering, alternative energy and energy efficiency to fusion, hydrogen and superconductor technologies.

Back to home

Comments (0)

Write a comment

Newest articles

Probing the depths of complex electron shells

HZDR team unveils new insights into uranium’s tricky chemistry. The heavy metal uranium is, besides its radioactive reputation, known for its intricate chemistry and diverse bonding behaviors. Now, an international…

Researchers create a one-dimensional gas out of light

Physicists at the University of Bonn and the University of Kaiserslautern-Landau (RPTU) have created a one-dimensional gas out of light. This has enabled them to test theoretical predictions about the…

GaN transistors and high-power amplifiers

… for millimeter wave satellite communications. With increasing data rates in mobile communications, the need for more powerful high-frequency electronics is growing. This is particularly true for satellite-based global communication…

Partners & Sponsors